CPM-3V *Surface Ground .125"- See Length Note
We buy this in 36" lengths and sell it in 12", 24" and 36" lengths.
If you buy 1ea, you will get a stick 12" long by the width and thickness shown.
If you buy 2, you will get a bar that is 24" in legnth.
If you buy 3, you will get a bar that is 36" in legnth.
**If you buy 2 or 3 and want 12" length pieces, please specify in the comments section that you would like them cut into 12" pieces.
**Advertised price is for 1qty 12" piece
CPM3V Bar Stock
- Surface Ground
This is CPM 3V.
CPM 3V offers impact toughness greater than A2, D2 Cru-Wear or CPM M4, approaching the level of S7 (commonly used in dies) and other shock resistant steels. This is one the super steels that is quietly gaining a rabid fan base. Especially in folder makers but this steel is so tough, it will make even better big hunters, Bowies or even choppers. It is tough and holds an edge. The edge holding is just slightly less than CPMS30V.
Carbon is .8%
Chromium is 7.5%
Vanadium is 2.75%
Molybdenum is 1.3%
With Chrome at 7.5%, this steel is not stainless steel. You need +11% or +13% (depending on who is deciding) Chromium to be called stainless.
Like all CPM steels is slightly "over sized" to common fractional thicknesses.
Note: CPM steel bar stock normally comes with a very hard black exterior from the foundry. This bar stock has been sand blasted by Crucible to remove most of the hard "bark" but there will still be deep surface marks and surface inclusions to grind away. The bar stock comes oversize to take this into account. The following dimensions are typical.
Nominal thickness Typical thickness
Tip: If you are going to cryo treat your blade with Dry Ice use kerosene instead of Acetone for the bath. It is still flammable but not as explosive as Acetone is.
The proprietary Crucible Particle Metallurgy (CPM®) process has been used for the commercial production of high speed steels and other high alloy tool steels since 1970. The process lends itself not only to the production of superior quality tool steels, but to the production of higher alloyed grades which cannot be produced by conventional steelmaking. For most applications the CPM process offers many benefits over conventionally ingot-cast tool steels.
Conventional Steelmaking vs.Particle Metallurgy Processing
Conventional steelmaking begins by melting the steel in a large electric arc furnace. It is usually followed by a secondary refining process such as Argon Oxygen Decarburization (AOD). After refining, the molten metal is poured from the furnace into a ladle, and then teemed into ingot molds.
Although the steel is very homogeneous in the molten state, as it slowly solidifies in the molds, the alloying elements segregate resulting in a non-uniform as-cast microstructure. In high speed steels and high carbon tool steels, carbides precipitate from the melt and grow to form a coarse intergranular network. Subsequent mill processing is required to break up and refine the microstructure, but the segregation effects are never fully eliminated. The higher the alloy content and the higher the carbon content, the more detrimental are the effects of the segregation on the resultant mechanical properties of the finished steel product.
The CPM process also begins with a homogeneous molten bath similar to conventional melting. Instead of being teemed into ingot molds, the molten metal is poured through a small nozzle where high pressure gas bursts the liquid stream into a spray of tiny spherical droplets. These rapidly solidify and collect as powder particles in the bottom of the atomization tower. The powder is relatively spherical in shape and uniform in composition as each particle is essentially a micro-ingot which has solidified so rapidly that segregation has been suppressed. The carbides which precipitate during solidification are extremely fine due to the rapid cooling and the small size of the powder particles. The fine carbide size of CPM steel endures throughout mill processing and remains fine in the finished bar.
The powder is screened and loaded into steel containers which are then evacuated and sealed. The sealed containers are hot isostatically pressed (HIP) at temperatures approximately the same as those used for forging. The extremely high pressure used in HIP consolidates the powder by bonding the individual particles into a fully dense compact. The resultant microstructure is homogeneous and fine grained and, in the high carbon grades, exhibits a uniform distribution of tiny carbides. Although CPM steels can be used in the as-HIP condition, the compacts normally undergo the same standard mill processing used for conventionally melted ingots, resulting in improved toughness.
CPM Eliminates Segregation
Conventionally produced high alloy steels are prone to alloy segregation during solidification. Regardless of the amount of subsequent mill processing, non-uniform clusters of carbides persist as remnants of the as-cast microstructure. This alloy segregation can detrimentally affect tool fabrication and performance.
CPM steels are HIP consolidated from tiny powder particles, each having uniform composition and a uniform distribution of fine carbides. Because there is no alloy segregation in the powder particles themselves, there is no alloy segregation in the resultant compact. The uniform distribution of fine carbides also prevents grain growth, so that the resultant microstructure is fine grained. Advantages of CPM
For the End User:
CRA means cold rolled annealed and is important to be in the description. It means the steel was pressure rolled while cold but was annealed again to relief the stress and take it to the softest state from rolling under tremendous pressure.
HR means hot rolled and this steel was rolled to thickness usually during the smelting process but maybe later. The steel generally will be half or nearly fully hard depending on the type. It may often have mill scale residue. This steel can be easily forged. It can also be ground via stock removal. Drilling a hole in the tang maybe hard to do with out a carbide bit.
HRA is the same but the steel was later annealed to relieve stress and make it as soft as possible for easier machining.
Several companies produce "powder" smelted steels. This is a premium smelting process that improves the mixing of alloy content and generally produces a finer grain structure as a result. The powder steels are nearly always annealed and can be assumed to annealed unless noted otherwise.